DESIGN AND FABRICATION OF TSVU (TRI COPTER SHAPED VTOL UAV) /

Tallennettuna:

Bibliografiset tiedot
Päätekijä:	Ferdausi, Mst.Jannatul
Yhteisötekijä:	Supervised by WG.Cdr S.A. Savanur (Professor, Department of Aeronautical Engineering, MIST, Dhaka.)
Muut tekijät:	Rabi Shankar Shil
Aineistotyyppi:	Kirja
Kieli:	englanti
Julkaistu:	Dhaka : AE DEPT MIST , c 2015.
Aiheet:	Thesis Paper of AE in B.Sc Prog. Aeronautical Engineering.
Tagit:	Lisää tagi Ei tageja, Lisää ensimmäinen tagi!

Samankaltaisia teoksia: DESIGN AND FABRICATION OF TSVU (TRI COPTER SHAPED VTOL UAV) /

Pikavilkaisu
DESIGN AND FABRICATION OF AIRFRAME STRUCTURE & CONTROLS OF UAV / Md. Fazlay Robbey, Md. Mukit Hasan, Saiful Islam .
Pikavilkaisu
DESIGN AND FABRICATION OF A MICRO UAV WITH DEVELOPMENT OF ITS STRUCTURE, PROPULSION AND CONTROL SYSTEM / Md. Tauhid Rahman Evan, Mir Md. Al Kahman Tamal, Md. Jamal Mian
Pikavilkaisu
INVESTIGATION OF DRAG EFFECT OF AROFOIL SHAPED FUSELAGE UAV MODEL AND VISUALIZATION OF AIR FLOW / Captain Md. Ruhul Amin Noor, Flying Officer Syeda Lira Rayhan & Flying Officer Umme Laila Amin
Pikavilkaisu
DESIGN AND FABRICATION OF THE FUSELAGE OF A RADIO CONTROLLED AERIAL VEHICLE /
Pikavilkaisu
DESIGN AND FABRICATION OF A GAS GENERATOR USING AN AUTO MOBILE TURBOCHARGER /
Pikavilkaisu
DESIGN AND FABRICATION OF AN UNMANNED AERIAL VEHICLE EATABLE OF DELIVERING MISSION PAYLOAD /
Pikavilkaisu
DESIGN & FABRICATION OF WING CONTROLS,UNDERCARRIAGE AND SKIN OF HOME BUILT EXPERIMENTAL AIRCRAFT’’ MIST X-01’’ /
Pikavilkaisu
DESIGN AND BUILD OF A SMALL FIXED WING UAV FOR SEARCH AND RESCUE APPLICATION /
Pikavilkaisu
ANALYSIS OF DESIGN FLAWS IN AN UNMANNED AERIAL VEHICLE (UAV) TARGET DRONE AND FABRICATION, CFD ANALYSIS AND TUNNEL TESTING OF A 3D MODEL POST AMENDMENT /
Pikavilkaisu
EFFECT OF CROSS –SECTIONAL SHAPES ON FREE JET CHARACTERIZATION NUMERICAL AND EXPERIMENTAL INVESTIGATION FEASIBLE AND PERFORMANCE OF DIFFERENT EXHAUST GEOMETRY /
Pikavilkaisu
DESIGN AND FABRICATION OF A TARGET DRONE /
Pikavilkaisu
SHAPE OPTIMIZATION OF GURNEY FLAP ON AIRFOIL /
Pikavilkaisu
DESIGN AND IMPLEMENTATION OF A COORDINATE UAV SWARM FOR LONG RANGE OPERATIONS /
Pikavilkaisu
DESIGN AND FABRICATION OF LUNAR DUST EXCAVATOR ROBOT /
Pikavilkaisu
DESIGN OF A FIXED WING JET PROPULSION POWERED UNMANNED AERIAL VEHICLE (UAV) TARGET DRONE /
Pikavilkaisu
ANALYSIS OF RADAR CROSS SECTION (RCS) OF DIFFERENT SHAPE OF TARGETS USING MICROSTRIP ANTENNA IN ORDER TO DESIGN & FABRICATE A PROTOTYPE OF LOW COST PHASED ARRAY RADAR /
Pikavilkaisu
DESIGNING, DEVELOPMENT & FABRICATION OF SPRING MASS DAMPER SYSTEM /
Pikavilkaisu
DESIGN AND FABRICATION OF AUTOMATIC FUEL TRANSFER SYSTEM OF AN AIRCRAFT /
Pikavilkaisu
DESIGN AND FABRICATION ON VACUUM ASSISTED INFUSIUN MOLDING SETUP FOR FABRICATION OF FLAT AND CURVED COMPOSITE PANELS /
Pikavilkaisu
"DESIGN,FABRICATION AND DEVELOPMENT OF AN UNMANNED AERIAL VEHICLE CAPABLE OF DELIVERING MISSION PAYLOAD"
Pikavilkaisu
DESIGN,ANALYSIS AND FABRICATION OF A FULLY ARTICULATED HELICOPTER MAIN ROTOR SYSTEM /
Pikavilkaisu
DESIGN AND FABRICATION OF AN AUTOPILOT MODEL TO INCORPORATE AUTOMATIC CONTROL OF THE MOMENT OF THE CONTROL SURFACES /
Pikavilkaisu
INVESTIGATION OF THE EFFECT OF DIFFERENT AIRFOIL SHAPED FUSELAGE ON THE PERFORMANCE OF AN UNMANNED AIR VEHICLE /
Pikavilkaisu
DESIGN , CONSTRUCTION AND PERFORMANCE CHECKING OF BLADE ANTENNA /