DESIGN AND FABRICATION OF TSVU (TRI COPTER SHAPED VTOL UAV) /

Gardado en:

Detalles Bibliográficos
Autor Principal:	Ferdausi, Mst.Jannatul
Autor Corporativo:	Supervised by WG.Cdr S.A. Savanur (Professor, Department of Aeronautical Engineering, MIST, Dhaka.)
Outros autores:	Rabi Shankar Shil
Formato:	Libro
Idioma:	inglés
Publicado:	Dhaka : AE DEPT MIST , c 2015.
Subjects:	Thesis Paper of AE in B.Sc Prog. Aeronautical Engineering.
Tags:	Engadir etiqueta Sen Etiquetas, Sexa o primeiro en etiquetar este rexistro!

Títulos similares: DESIGN AND FABRICATION OF TSVU (TRI COPTER SHAPED VTOL UAV) /

Quick Look
DESIGN AND FABRICATION OF AIRFRAME STRUCTURE & CONTROLS OF UAV / Md. Fazlay Robbey, Md. Mukit Hasan, Saiful Islam .
Quick Look
DESIGN AND FABRICATION OF A MICRO UAV WITH DEVELOPMENT OF ITS STRUCTURE, PROPULSION AND CONTROL SYSTEM / Md. Tauhid Rahman Evan, Mir Md. Al Kahman Tamal, Md. Jamal Mian
Quick Look
INVESTIGATION OF DRAG EFFECT OF AROFOIL SHAPED FUSELAGE UAV MODEL AND VISUALIZATION OF AIR FLOW / Captain Md. Ruhul Amin Noor, Flying Officer Syeda Lira Rayhan & Flying Officer Umme Laila Amin
Quick Look
DESIGN AND FABRICATION OF THE FUSELAGE OF A RADIO CONTROLLED AERIAL VEHICLE /
Quick Look
DESIGN AND FABRICATION OF A GAS GENERATOR USING AN AUTO MOBILE TURBOCHARGER /
Quick Look
DESIGN AND FABRICATION OF AN UNMANNED AERIAL VEHICLE EATABLE OF DELIVERING MISSION PAYLOAD /
Quick Look
DESIGN & FABRICATION OF WING CONTROLS,UNDERCARRIAGE AND SKIN OF HOME BUILT EXPERIMENTAL AIRCRAFT’’ MIST X-01’’ /
Quick Look
DESIGN AND BUILD OF A SMALL FIXED WING UAV FOR SEARCH AND RESCUE APPLICATION /
Quick Look
ANALYSIS OF DESIGN FLAWS IN AN UNMANNED AERIAL VEHICLE (UAV) TARGET DRONE AND FABRICATION, CFD ANALYSIS AND TUNNEL TESTING OF A 3D MODEL POST AMENDMENT /
Quick Look
EFFECT OF CROSS –SECTIONAL SHAPES ON FREE JET CHARACTERIZATION NUMERICAL AND EXPERIMENTAL INVESTIGATION FEASIBLE AND PERFORMANCE OF DIFFERENT EXHAUST GEOMETRY /
Quick Look
DESIGN AND FABRICATION OF A TARGET DRONE /
Quick Look
SHAPE OPTIMIZATION OF GURNEY FLAP ON AIRFOIL /
Quick Look
DESIGN AND IMPLEMENTATION OF A COORDINATE UAV SWARM FOR LONG RANGE OPERATIONS /
Quick Look
DESIGN AND FABRICATION OF LUNAR DUST EXCAVATOR ROBOT /
Quick Look
DESIGN OF A FIXED WING JET PROPULSION POWERED UNMANNED AERIAL VEHICLE (UAV) TARGET DRONE /
Quick Look
ANALYSIS OF RADAR CROSS SECTION (RCS) OF DIFFERENT SHAPE OF TARGETS USING MICROSTRIP ANTENNA IN ORDER TO DESIGN & FABRICATE A PROTOTYPE OF LOW COST PHASED ARRAY RADAR /
Quick Look
DESIGNING, DEVELOPMENT & FABRICATION OF SPRING MASS DAMPER SYSTEM /
Quick Look
DESIGN AND FABRICATION OF AUTOMATIC FUEL TRANSFER SYSTEM OF AN AIRCRAFT /
Quick Look
DESIGN AND FABRICATION ON VACUUM ASSISTED INFUSIUN MOLDING SETUP FOR FABRICATION OF FLAT AND CURVED COMPOSITE PANELS /
Quick Look
DESIGN,ANALYSIS AND FABRICATION OF A FULLY ARTICULATED HELICOPTER MAIN ROTOR SYSTEM /
Quick Look
DESIGN AND FABRICATION OF AN AUTOPILOT MODEL TO INCORPORATE AUTOMATIC CONTROL OF THE MOMENT OF THE CONTROL SURFACES /
Quick Look
"DESIGN,FABRICATION AND DEVELOPMENT OF AN UNMANNED AERIAL VEHICLE CAPABLE OF DELIVERING MISSION PAYLOAD"
Quick Look
INVESTIGATION OF THE EFFECT OF DIFFERENT AIRFOIL SHAPED FUSELAGE ON THE PERFORMANCE OF AN UNMANNED AIR VEHICLE /
Quick Look
DESIGN , CONSTRUCTION AND PERFORMANCE CHECKING OF BLADE ANTENNA /