DESIGN AND FABRICATION OF LUNAR DUST EXCAVATOR ROBOT /

Shranjeno v:

Bibliografske podrobnosti
Glavni avtor:	Rumi, Md Jalal Uddin
Korporativna značnica:	Supervised by Group Captain Md Abdus Salam (Head and Senior Instructor, Department of AE, MIST.)
Drugi avtorji:	Jony, Bodiuzzaman, Eunus, H.E.M. Zahidul Islam
Format:	Knjiga
Jezik:	angleščina
Izdano:	Dhaka : AE DEPT. MIST, c2012.
Teme:	Aeronautical Engineering This Thesis Paper of AE in B.Sc Program.
Oznake:	Označite Brez oznak, prvi označite!

Podobne knjige/članki: DESIGN AND FABRICATION OF LUNAR DUST EXCAVATOR ROBOT /

Quick Look
INFLUENCE OF HEAT TREATMENT ON ELECTROMECHANICAL PROPERTIES OF ALUMINUM COMPOSITES /
Quick Look
DESIGN AND FABRICATION OF A TARGET DRONE /
Quick Look
"DESIGN, FABRICATION AND DEVELOPMENT OF A SMALL SURVEILLANCE UNMANNED AERIAL VEHICLE CAPABLE OF DETECTING OBJECTS IN FLOOD AFFECTED AREA IN REAL TIME" /
Quick Look
DESIGNING, DEVELOPMENT & FABRICATION OF SPRING MASS DAMPER SYSTEM /
Quick Look
DESIGN AND FABRICATION OF AUTOMATIC FUEL TRANSFER SYSTEM OF AN AIRCRAFT /
Quick Look
DESIGN AND FABRICATION OF AN AUTOPILOT MODEL TO INCORPORATE AUTOMATIC CONTROL OF THE MOMENT OF THE CONTROL SURFACES /
Quick Look
DESIGN AND FABRICATION OF AIRFRAME STRUCTURE & CONTROLS OF UAV / Md. Fazlay Robbey, Md. Mukit Hasan, Saiful Islam .
Quick Look
DESIGN,ANALYSIS AND FABRICATION OF A FULLY ARTICULATED HELICOPTER MAIN ROTOR SYSTEM /
Quick Look
"DESIGN,FABRICATION AND DEVELOPMENT OF AN UNMANNED AERIAL VEHICLE CAPABLE OF DELIVERING MISSION PAYLOAD"
Quick Look
DESIGN AND FABRICATION OF THE FUSELAGE OF A RADIO CONTROLLED AERIAL VEHICLE /
Quick Look
DESIGN AND FABRICATION OF TSVU (TRI COPTER SHAPED VTOL UAV) /
Quick Look
DESIGN AND FABRICATION ON VACUUM ASSISTED INFUSIUN MOLDING SETUP FOR FABRICATION OF FLAT AND CURVED COMPOSITE PANELS /
Quick Look
DESIGN AND FABRICATION OF A FIXED-WING (UNMANNED AERIAL VEHICLE) TARGET DRONE FOR TESTING OF AIR DEFENSE SYSTEM /
Quick Look
DESIGN AND FABRICATION OF A GAS GENERATOR USING AN AUTO MOBILE TURBOCHARGER /
Quick Look
DESIGN AND FABRICATION OF AN UNMANNED AERIAL VEHICLE EATABLE OF DELIVERING MISSION PAYLOAD /
Quick Look
ANALYSIS OF RADAR CROSS SECTION (RCS) OF DIFFERENT SHAPE OF TARGETS USING MICROSTRIP ANTENNA IN ORDER TO DESIGN & FABRICATE A PROTOTYPE OF LOW COST PHASED ARRAY RADAR /
Quick Look
DESIGN AND FABRICATION OF A MICRO UAV WITH DEVELOPMENT OF ITS STRUCTURE, PROPULSION AND CONTROL SYSTEM / Md. Tauhid Rahman Evan, Mir Md. Al Kahman Tamal, Md. Jamal Mian
Quick Look
DESIGN AND FABRICATION OF PNEUMATIC GRIPPER FOR ROBOTIC MANIPULATION /
Quick Look
FABRICATION OF AL-6063 METAL MATRIX HYBRID COMPOSITE REINFORCED WITH SIC NANOPARTICALS BY STRI CASTING /
Quick Look
ANALYSIS OF DESIGN FLAWS IN AN UNMANNED AERIAL VEHICLE (UAV) TARGET DRONE AND FABRICATION, CFD ANALYSIS AND TUNNEL TESTING OF A 3D MODEL POST AMENDMENT /
Quick Look
Fabrication and Property Investigation of SiC Reinforced Aluminium based Metal Matrix Composite for Aerospace materials /
Quick Look
DESIGN, FABRICATION,AND FLIGHT TESTING OF GHOST WING "GW-1" MAV /
Quick Look
EXCAVATION DESIGN BASED ON MECHANICAL PROPERTIES OF HARD ROCK /
Quick Look
DESIGN & FABRICATION OF WING CONTROLS,UNDERCARRIAGE AND SKIN OF HOME BUILT EXPERIMENTAL AIRCRAFT’’ MIST X-01’’ /